Search
Menu Close
Menu Close

Hearing Aid Loop Amplifier - 240W @ 10A/600 sqm

Manufacturer: ITC
Public Address Hearing Aid Loop Amplifier.
  • 240 watt amplifier covers up to 600 m² for hearing loops.
  • High power current-driven design ensures excellent audio quality for users.
  • Three mic/line inputs with a priority input for voice alarm systems.
  • Built-in limiter and Automatic Gain Control for optimal sound management.
  • Stackable configuration allows coverage of larger areas if needed.
SKU: T-10ALP
Availability: In stock
$1,999.00 incl tax
i h

Hearing Loop Amplifier - 240 watt amplifier for induction hearing aid loops installed in the floor or ceiling of a venue. Up to 600 m2 can be covered per amplifier. This enables hearing-aid users in the area enclosed by the wire loop to hear all audio announcements, sound or music broadcast. Hearing-aid users can set their devices to T-mode to receive the signal coming from the loop and receive excellent audio-quality announcements, without the background noise or reverberation that normally impairs intelligibility for people with hearing difficulties.

Features

  • High power current driven amplifier
  • Power output 240 watts 10A
  • Three mic/line inputs, one priority input (100 V)
  • Selectable frequency range and tone controls
  • Limiter and Automatic Gain Control
  • Integrates in an voice evacuation system
  • Coverage around 600m per amplifier
  • Volume control for inputs 1-3 and master, treble & bass tone control
  • Extensive protection includes high temp, overload and short circuit

Functions

The loop amplifier can be connected to a mixing amplifier's line level output, or it can accept up to three microphone/line signals directly. A 100 V priority input is available for uplink to a voice alarm system. This input can be monitored for the presence of a pilot tone. The built-in supervision monitors all key functions of the loop amplifier, and the fault state is available on a fail-safe relay.

The Loop amplifier is fitted with a limiter to limit the output field strength to the prescribed 100 mA/m. This circuitry can also be set to function as an Automatic Gain Control (AGC), so those soft signals are boosted for intelligibility while loud signals are attenuated so that all information is presented at a comfortable listening level. To adjust the sound to the program material and the environment,   one controls and a metal loss compensation circuit is available. After installation the controls can be locked to prevent unwanted access.

Even though one Loop Amplifier can cover up to 600m , the Loop Amplifier is stackable (master/slave configuration), to cover very large areas. Also, low spill schemes are supported. Its unique quadrate configuration provides uniform field strengths over multiple loops 

A Hearing Aid Loop Amplifier. Cost-effective and designed to drive a wire loop installed in the floor or ceiling of a venue up to 600 m sq. +High power, current driven amplifier +Three microphone/line inputs, one priority input (100 V) + Selectable frequency range and tone controls + Limiter and automatic gain control (AGC) + Integrates in an EN 54-16 and EN 60849 compliant system It enables hearing-aid users in the area enclosed by the wire loop to hear all announcements, soundtrack or music in a high quality without the background noise and reverberation that normally impairs intelligibility for people with hearing difficulties.

Model

T-10ALP

Max Output Current

10A

Rated Current Outputs

7A

Input Sensitivity & Impedance

Input1-3(MIC): 2.5mV/600 , Balanced XLR input

Input1-3(LINE): 775mV/10K , Balanced XLR input

Output Sensitivity & Impedance

1V/470 , Balanced XLR output

Tone Control

Bass: 10dB at 100Hz

Treble: 10dB at 10KHz

Frequency Response

50Hz~10KHz ( 3dB)

S/N Ratio

66dB

THD

Less than 0.1% at 1KHz, 1/3 rated power

Muting Function

Input 1 overrides other input signals with 0-30dB attenuation

Connector

Screw

Master Input

Connector 1/4" TS jack

Crosstalk

50dB

100V Input

Transformer balanced. Impedance >100k

90 Slave O utput

1V/470 , Unbalanced Connector 1/4" TS jack

0 Slave O utput

1V/470 , Unbalanced Connector 1/4" TS jack

Phantom Power

+48V

Cooling

Fan automatically start up when temp reaches 55

Protection

High temp, overload & short-circuit

Power Supply

~110V/60Hz or ~230V/50Hz

Power Consumption

500W

Weight

10.3Kg

Dimensions

484x303x88mm

Finish

Panel: aluminum plate, black

Case: steel plate, black

 

 

0.0 0
Write your own review Close
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
*
*
*